Facebook yachts@seaforceix.com 1+ 941.721.9009

55.5 Quad Outboard - Cuddy Arrangement

55.5 Performance Sport Outboard
Length Overall 55’-8” 
Beam 15’-4" 
Generator 17kw marine diesel
Fuel Capacity 1,000 gallons (usable)
Fresh Water Capacity 100 gallons
Other Chilled water A/C, water heater
Standard Propulsion Horsepower

4 x 425 hp (Yamaha)

Other Images Click Here

 

Standard Equipment

Contact for Full Specifications

Machinery

  • Quad Yamaha outboard engines rated at 425hp each (Seven marine available)
  • 12vdc starting and electrics
  • Helm Master steering
  • Custom paint
  • Stainless steel propeller
  • Single 17kw marine diesel generator 120/240vac, 60hz, single phase
  • 12vdc starting
  • Fresh water cooling system
  • Vibration mounts
  • Automatic low oil-high temp safety shut-down
  • Remote control and monitoring panel
  • Remote start stop switches on the helm
  • Sound shield
  • Fiberglass lift muffler for generator exhaust
  • Machinery compartment blower
  • Three zone bilge system with four bilge pumps
  • Three aluminum fuel tanks – 1,000 US gallons total capacity
  • Fuel tanks have 2” deck fills, dual vents and ball valves on pick-up tubes
  • Aluminum water tank –100 US gallon water tank with 1 ½” fill
  • Aluminum holding tank– 40 US gallon capacity with deck plate and 12vdc overboard discharge pump
  • Fuel, water and holding tanks have level senders
  • Gray-water tank with submersible 12vdc pump for head sink, shower and air conditioning condensate drain.
  • Chilled water air conditioning
  • 12vdc fresh water pressure pump
  • 11 gallon water heater
  • 12vdc marine toilets with diverter valve to the holding tank or overboard
  • On demand 12vdc cockpit salt-water wash-down service.
  • Each outboard draws fuel through selector valves connected to each tank.
  • Fuel filter/water separator for each outboard engine
  • Single fuel filter for the generator
  • All fuel supply hoses are USCG Type 1 with brass fittings
  • A fire suppression system for the machinery compartment – Note: system is “rate of rise” activated, with shutdown circuits for generator and blower.
  • Oil-less air compressor with storage tank and dual trumpet air horn
  • Flush mounted stainless steel trim tabs
  • 900 GPD water maker
  • 10” bow thruster with control panel at main helm
  • ** Sea Keeper stabilizer is available as an option

Electrical

  • One 17,000 watt 120/240vac 60hz, 1 phase marine diesel generator
  • One 50’ 50amp 120/240vac 60hz, 1 phase shore cord
  • One 15kva isolation transformer
  • Two sources of power are switch selected from the A.C control panel to energize the A.C. power bus
  • Six, 12vdc AGM batteries. One for each outboard engine and two paralleled wired for generator start and 12vdc service
  • Each bank has a disconnect switch
  • Emergency power paralleling solenoids
  • Two 40 amp battery chargers
  • Breaker panel distribution system
  • All wiring meets A.B.Y.C. recommendations
  • Alarm system with helm display panel monitors high water, smoke and high carbon monoxide with a visual and auditory alarm.
  • All underwater metals are connected to a common bonding system that terminates at the sacrificial zinc anodes.
  • All wire is tinned copper wire with 105C jacket rating
  • Hull mounted ground plate
  • 12vdc LED overhead lighting for interior
  • 12vdc LED white/blue exterior lighting

Interior - See General Arrangement

  • General Arrangement: Raised helm area with double helm chair and raised bench seating for Three. The cabin area will have two staterooms, two heads, full galley and settee with pedestal table.
  • Interior to be constructed of Anigre wood with clear 60/40 satin finish. Other woods available.
  • Counter top is solid surfacing material
  • Vinyl flooring

Exterior

  • Hatches for service area access.
  • Eight 12” stainless steel pop up cleats through bolted with aluminum backing plates
  • White rub rail with stainless steel insert
  • Stainless steel tank fills and vents
  • Signal and electronics mast with COLREG running lights
  • One 50 amp 120/240 shore cord inlet
  • Stainless steel anchor chute with stainless steel bow guard
  • 2000# vertical windlass
  • Anchor, 200’ ¾” rope and 10’ chain
  • Four 40’ dock lines and four 10” fenders
  • The entire bottom is coated with a layer of epoxy and a layer of anti-fouling paint
  • All topside surfaces are faired, primed and finished with Awlcraft 2000 topcoat
  • Aluminum hand rails
  • Glass windshield
  • Remote control spot light
  • Four exterior speakers
  • 8 PFDs

Testing and Delivery

  • Two, six hour test trips with all major equipment suppliers and necessary yard personnel. All equipment will be thoroughly tested for proper function. This includes one week of area dockage, licensed captain and fuel.

Construction

  • AME 5000 Vinylester resin throughout
  • Divinycell foam core throughout – solid glass in critical areas
  • Composite soles and bulkheads
  • Secondary bonds with epoxy resin
  • Comprehensive full-length stringers and thwart structural grid
  • Bilges painted
  • MONOLITHIC CONSTRUCTION – All major fiberglass components are fully engineered, cored structures constructed using high physical and heat rated materials. The components are then baked for complete cure and stabilization. This allows the vessel to be painted any color. The components are then assembled and glassed together using non-woven glass and epoxy resin. All the soles, bulkheads and cabin walls are likewise glassed to the hull and deck. The result is a weight conscious structure that works as a single unit.
Copyright © Seaforce IX All Rights Reserved
Maintained by Sitespring, Inc.